This is my config file, can not find it.
; This is the configuration file for an Yaesu FT-817 transceiver
; Use "," for parameters separation
Brand=Yaesu
Model=FT817
Pic=ft817.jpg
sigRadios=$1gR@d10s
; Frequency coverage
FRANGE=100000-56000000,76000000-154000000,420000000-470000000
; List of available Bands
BANDS=160m,80m,40m,30m,20m,17m,15m,12m,11m,10m,6m,4m,2m,70cm
; first wheel - list of available modes in the MODE wheel (starts with wheel name)
LST1NAME=MODE
LST1ITEMS=LSB,USB,CW,CWR,AM,FM,DIG
LST1CMDS=CMD_SET_MODE_LSB,CMD_SET_MODE_USB,CMD_SET_MODE_CW,CMD_SET_MODE_CWR,CMD_SET_MODE_AM,CMD_SET_MODE_FM,CMD_SET_MODE_DIG
; second wheel - list of available powers in the PWR wheel (starts with wheel name)
LST2NAME=PWR
LST2ITEMS=0.5W,1.0W,2.5W,5.0W
LST2CMDS=CMD_SET_PWR_0.5W,CMD_SET_PWR_1.0W,CMD_SET_PWR_2.5W,CMD_SET_PWR_5.0W
; Option Button config (name,odd_press_cmd,even_press_cmd,odd_press_label,even_press_label
BTN_OPT1_NOFN=VFO,CMD_SET_VFO_A=VFO-A,CMD_SET_VFO_B=VFO-B
BTN_OPT2_NOFN=NB,CMD_SET_NB_OFF=OFF,CMD_SET_NB_ON=ON
BTN_OPT3_NOFN=AGC,CMD_SET_AGC_OFF=OFF,CMD_SET_AGC_SLOW=SLOW,CMD_SET_AGC_FAST=FAST,CMD_SET_AGC_AUTO=AUTO
BTN_OPT4_NOFN=
BTN_OPT5_NOFN=ATT,CMD_SET_ATT_OFF=OFF,CMD_SET_ATT_ON=ON
BTN_OPT1_FN=
BTN_OPT2_FN=
BTN_OPT3_FN=
BTN_OPT4_FN=
BTN_OPT5_FN=
; List of available commands for the current transceiver, all items from the list are one byte equivalent, BCD (2 digits as chars) or strings
; <Pxxxx> as 'byte' to separate two successive commands by a xxxx ms delay
; <Dxx> - frequency numeric digits - BCD packed (from 9, thousands MHz to 0 - Hz)
; <Cx> - frequency char digit (from 9, thousands MHz to 0 - Hz)
; <Sxxxxxxx> - string xxxxxx)
; <#param;value> - set app internal parameter to value
; xx,xx,... - bytes represented as hex string values
; <MxXXXXXXXX=val> - send an EEPROM memory location; x=1:locatia adresata, x=2:urmatoarea locatie, XXXXXXXX:binary mask, val:binary value to include in the mask zone
CMD_SET_FREQ=<D87>,<D65>,<D43>,<D21>,01
CMD_SET_PTT_ON=00,00,00,00,08
CMD_SET_PTT_OFF=00,00,00,00,88
CMD_SET_MODE_LSB=00,00,00,00,07
CMD_SET_MODE_USB=01,00,00,00,07
CMD_SET_MODE_CW=02,00,00,00,07
CMD_SET_MODE_CWR=03,00,00,00,07
CMD_SET_MODE_AM=04,00,00,00,07
CMD_SET_MODE_FM=08,00,00,00,07
CMD_SET_MODE_DIG=0A,00,00,00,07
CMD_SET_MODE_PKT=0C,00,00,00,07
CMD_SET_VFO_A=00,55,10100000,00,BC
CMD_SET_VFO_B=00,55,10100001,00,BC
; EEPROM 0057:
; 1,0[00 = Auto, 01 = Fast, 10 = Slow, 11 = Off AGC Mode]
; 2[0 = Off, 1 = On (Display format)]
; 3[0]
; 4[0 = Off, 1 = On (Passband Tuning)]
; 5[0 = Off, 1 = On (Noise Blanker)]
; 6[0 = Off, 1 = On (Dial Lock)]
; 7[0 = Off, 1 = On (Fast tuning)]
; EEPROM 0058:
; 1,0[00 = PWR, 01 = ALC, 10 = SWR, 11 = MOD (Pwr Meter Mode)]
; 2[0 = Normal, 1 = Reverse (CW Paddle Normal/Reverse (#19))]
; 3[0]
; 4[0 = Off, 1 = On (CW Keyer)]
; 5[0 = Off, 1 = On (Semi Break-In)]
; 6[0 = Off, 1 = On (Voltmeter Display)]
; 7[0 = Off, 1 = On (VOX On/Off)]
; hex values to initialize EEPROM locations 57 and 57 (in hex)
EEPROM0057=00
EEPROM0058=40
;CMD_SET_AGC_OFF=00,57,<M111111100=0>,<M211111111=00>,BC
;CMD_SET_AGC_SLOW=00,57,<M111111100=2>,<M211111111=00>,BC
;CMD_SET_AGC_FAST=00,57,<M111111100=1>,<M211111111=00>,BC
;CMD_SET_AGC_AUTO=00,57,<M111111100=3>,<M211111111=00>,BC
CMD_SET_SPLIT_ON=00,00,00,00,02
CMD_SET_SPLIT_OFF=00,00,00,00,82
CMD_SET_LOCK_ON=00,00,00,00,00
CMD_SET_LOCK_OFF=00,00,00,00,80
CMD_SET_CLARIFIER_ON=00,00,00,00,05
CMD_SET_CLARIFIER_OFF=00,00,00,00,85
CMD_SET_DCS_ON=0A,00,00,00,0A
CMD_SET_CTCSS_ON=2A,00,00,00,0A
CMD_SET_ENCODER_ON=4A,00,00,00,0A
CMD_SET_ENCODER_OFF=8A,00,00,00,0A
CMD_SET_POWER_ON=00,00,00,00,80,<P1000>,00,00,00,00,0F,
CMD_SET_POWER_OFF=00,00,00,00,80,<P1000>,00,00,00,00,8F,<P1000>
; EEPROM WRITE
; MSB LSB Data4Address Data4Address+1 BC
CMD_SET_PWR_0.5W=00,79,03,00000000,BC
CMD_SET_PWR_1.0W=00,79,02,00000000,BC
CMD_SET_PWR_2.5W=00,79,01,00000000,BC
CMD_SET_PWR_5.0W=00,79,00,00000000,BC
; read commands format
; command,separator(<R>)nr.of.expected.bytes/binary mask if one byte answer or bytes order (<Bx> if multiple bytes, where 0 is used for dummy byte (if any)
;CMD_READ_FREQ=00,00,00,00,03,<R>,<D87>,<D65>,<D43>,<D21>,<00>
;CMD_READ_MODE=00,00,00,00,03,<R>,<00>,<00>,<00>,<00>,<00=LSB;01=USB;02=CW;03=CWR;04=AM;06=WFM;08=FM;0A=DIG;0C=PKT>
;CMD_READ_SMETER=00,00,00,00,E7/<00001111>
;CMD_READ_SWR=00,00,00,00,F7/<00001111>
;CMD_READ_ALC=00,00,00,00,F7/<00001111>
;CMD_READ_MOD=00,00,00,00,F7/<00001111>
; list of commands to be sent at startup (usually read different parameters in order to be able to work after that without feedback, for max. responsiveness
STARTUP=CMD_SET_LOCK_OFF
Newest update No HRD?
Re: Newest update No HRD?
Hi,
This is the section:
CMD_SET_PWR_0.5W=00,79,03,00111111,BC
CMD_SET_PWR_1.0W=00,79,02,00111111,BC
CMD_SET_PWR_2.5W=00,79,01,00111111,BC
CMD_SET_PWR_5.0W=00,79,00,00111111,BC
And rear antenna will be used for all the bands.
73 Dan YO3GGX
This is the section:
Just change it to:iw1ghg wrote:This is my config file, can not find it.
CMD_SET_PWR_0.5W=00,79,03,00000000,BC
CMD_SET_PWR_1.0W=00,79,02,00000000,BC
CMD_SET_PWR_2.5W=00,79,01,00000000,BC
CMD_SET_PWR_5.0W=00,79,00,00000000,BC
CMD_SET_PWR_0.5W=00,79,03,00111111,BC
CMD_SET_PWR_1.0W=00,79,02,00111111,BC
CMD_SET_PWR_2.5W=00,79,01,00111111,BC
CMD_SET_PWR_5.0W=00,79,00,00111111,BC
And rear antenna will be used for all the bands.
73 Dan YO3GGX
Re: Newest update No HRD?
I had not read well in the post.
Thank you, everything ok, I solved it.
Thank you, everything ok, I solved it.
Re: Newest update No HRD?
Great!
You can play with the config file and add any available command you need to one of the 10 option buttons.
Good luck.
Dan YO3GGX
You can play with the config file and add any available command you need to one of the 10 option buttons.
Good luck.
Dan YO3GGX